Dielectric and mechanical properties of CaCu3Ti3.925(Nb0.5Al0.5)0.075O12 & Al reinforced epoxy-composites (0–3) for embedded capacitor applications

CaCu₃Ti_3.925(Nb_0.5Al_0.5)_0.075O₁₂ [CCTNAO] ceramics were synthesized by microwave assisted solid state reaction technique. CCTNAO ceramics possessed room temperature (RT) dielectric constant (ε_r) ～ 24,173 with tanδ ～0.149 at 1 kHz frequency. Commercially available epoxy-resin, hardener, Al-powder along with CCTNAO powder were used to prepare epoxy based 0–3 composites. Maximum ε_r ～33.37 with tanδ ～0.107 at RT were obtained for 40 vol% CCTNAO loading in epoxy. For x = 0.2 in (1-x)[0.8 Epoxy-0.2 CCTNAO]-x Al Epoxy composites, highest ε_r ～77.6 with tanδ ～ 0.15 at 1 kHz frequency were observed. Increase in ε_r with the increase of Al filler content in composites is attributed to interfacial polarization and cluster formations. Different theoretical models were discussed to explain the dielectric properties of synthesized composites. Experimentally measured values of ε_eff were in close agreement with EMT model (n = 0.13) and Yamada Model (η = 7). An empirical proposed power law ε_eff = ε_m(1+x)ⁿ, with n ～ 10 had a considerable agreement with the experimental results. Vickers hardness test study was carried out to ascertain the mechanical properties of the synthesized composites.     

Dense and core-rim structured B4C-TiB2 ceramics with Mo-Co-WC additive

B₄C-TiB₂ ceramics (TiB₂ ranging 5~70 vol%) with Mo-Co-WC as the sintering additive were prepared by spark plasma sintering. In comparison with B₄C-TiB₂ without additive, the enhanced densification was evident in the sintered specimen with Mo-Co-WC additive. Core-rim structured grain was observed around TiB₂ grains. The interface of the rim between TiB₂ and B₄C phases demonstrated different feature: the inner borderline of the rim exhibited a smooth feature, whereas a sharp curved grain boundary was observed between the rim and the B₄C grain. The formation mechanism is discussed: the epitaxial growth of (Ti,Mo,W)B₂ rim around the TiB₂ core may occur as a result of the solid solution and dissolution-precipitation between TiB₂ phase and the sintering additive. It was revealed that the fracture toughness increased as the content of TiB₂ content increased, alongside the decreased hardness. B₄C-30 vol% TiB₂ specimen demonstrated the optimal combination of mechanical properties, reaching Vickers hardness of 24.3 GPa and fracture toughness of 3.33 MPa·m^1/2.     

Repeated low-velocity impact responses of SiC particle reinforced Al metal-matrix composites

This study aimed to investigate experimentally the repeated low-velocity impact behaviors of SiC reinforced aluminum 6061 metal-matrix composites for different volume fractions and energy levels. In addition, the hardness variations were measured by the Vickers hardness tests from the impacted and impact-free cross-sections of the particle reinforced metal-matrix composites. Low-velocity impact tests were applied to composite samples manufactured by powder metallurgy (in 10, 20, and 30% volume fractions) at two total energy levels (15 and 60 J as single) and in repetitions equal to the sum of these energy levels (5 + 5 + 5 and 20 + 20 + 20 J as repeated). As a result, in increasing the impact number for all volume fractions, the total contact time was shortened and the peak contact force increased, whereas both the permanent central deflection and the absorbed energies reduced. Hence, these variations obtained under repeated impacts (5 + 5 + 5 and 20 + 20 + 20 J) revealed that metal-matrix composites showed a tougher behavior with an increase in the impact numbers from 1st to 3rd, particularly because of the strain hardening effect. Furthermore, an increase in volume fraction from 10 to 30% resulted in an increase in the impact strength under all repeated and single impacts despite changing deformation and damage mechanisms due to increasing the strain hardening effect and particle fractures. The hardness was affected by the volume fraction and increased as the volume fraction increased in both the impacted and impact-free zones. The repeated impact increased the impacted zone hardness more than the single impact for all volume fractions. Additionally, the hardness of the impacted zone under 20 + 20 + 20 J repeated impact was measured as the highest value in the 30% volume fraction. Therefore, metal-matrix composites can behave harder with the strain hardening effect under repeated impacts.     

Structure,mechanical and thermal properties of Y-doped CrAlN coatings

CrAlYN coatings with different Y contents (0, 5 and 12 at.%) were deposited by cathodic arc evaporation to investigate the influence of Y-addition on the structure, mechanical and thermal properties of CrAlN coatings by using X-ray diffraction, scanning electron microscopy, differential scanning calorimetry, thermal gravimetric analysis and nanoindentation. The structural transformation of single phase cubic Cr_0.42Al_0.58N and Cr_0.39Al_0.56Y_0.05N coatings to cubic–wurtzite mixed Cr_0.32Al_0.56Y_0.12N coating leads to a drop in hardness from (30.2±0.7) GPa of Cr_0.42Al_0.58N and (32.0±1.0) GPa of Cr_0.39Al_0.56Y_0.05N to (25.2±0.7) GPa of Cr_0.32Al_0.56Y_0.12N. The incorporation of 5 at.% Y retards the thermal decomposition of CrAlN, verified by the postponed precipitation of w-AlN and N-loss upon annealing. Correspondingly, Cr_0.39Al_0.56Y_0.05N coating consistently exhibits the highest hardness value during thermal annealing. Nevertheless, alloying with Y exerts an adverse effect on the oxidation resistance of CrAlN.     

巨型水轮发电机剪断销研发与质量控制

为获得设计需要的巨型水轮发电机剪断销的剪切力,得到剪切力波动受控的批量剪断销,通过拉伸试验、冲击试验、硬度试验和剪断销剪切试验等讨论了全尺寸剪断销剪切试验的可行性,分析了剪切试验时正常剪断和非正常剪断的剪断销材料性能差异,探究了剪断销的剪切力质量稳定性控制方法。结果表明:控制剪断销料坯的布氏硬度波动,可实现间接控制剪断销剪切强度的波动;通过试验总结的六步法可达到控制批量剪断销质量和剪切力波动的目的。     

Densification effects on the fracture in fused silica under Vickers indentation

This study investigates the effects of densification on the deformation and fracture in fused silica under Vickers indentation by both the finite element analysis (FEA) and experimental tests. A refined elliptical constitutive model was used, which enables us to investigate the effects of the evolution of yield stress under pure shear and elastic properties with densification. The densification distribution was predicted and compared with experiments. The plastic deformation and indentation stress fields were used to analyze the initiation and morphology of various crack types. The formation mechanism of borderline cracks was revealed for the first time. This study reveals that the asymmetry of the densification distribution and elastic-plastic boundary significantly influences the cracking behavior. Under the Vickers indentation, conical cracks have the largest penetration depth. When these cracks emerge from a region far from the impression, they extend with constant radii to form circles on the sample surface. Otherwise, they tend to be initiated at the centers of the indenter-material contact edges before propagating towards the impression corners with increasing radii. Therefore, the borderline cracks consisting of successive partial conical cracks can form at a low load and makes them the first type of crack to appear.     

Wear resistance and hardness properties of TiB2– Fe coating developed on AISI 1020 steel by tungsten inert gas (TIG) cladding

The present work is attempted to improve the microhardness and wear properties of AISI 1020 steel by depositing TiB₂–Fe composite coating using tungsten inert gas (TIG) cladding. In this study, different compositions of TiB₂–Fe paste form were preplaced on the substrate plates and then TIG heat input was applied to deposit hard composite coating layer. The main objective of the present work was to explore the influence of TIG input current as well as iron content on the microstructure and surface properties of deposited coatings. Microhardness, microstructural and phase characterization of the coating have been done by the Vickers microhardness tester, scanning electron microscope (SEM), Energy dispersive spectroscopy (EDS) and X-ray diffractrometer (XRD). The results showed that the microhardness of the TiB₂–Fe coating was strongly influenced by the composition of the coating materials as well as the TIG processing current. The microhardness increases with decreasing Fe contents in the coating materials with constant processing current (90 A) as well as it also increases with decreasing processing current with the fixed composition of coating materials (80TiB₂–20Fe). The maximum average microhardness found was 3082 HV_0.1 for the coating of 100TiB₂–0Fe composition ratio and 90 A processing current which was about 18 times higher than that of the substrate average microhardness value (163 HV_0.1). Average wear rate evaluated by considering weight loss of the TIG cladded samples using pin on disc tribometer by the sliding distance of 864 m and 20 N normal loads. The wear results also showed that the coating contains 100 wt% of TiB₂ (0 wt% of Fe) exhibited lower rate of wear 6.74 × 10^?8 g/Nm which is about 24 times lower as compared to AISI 1020 mild steel wear rate (166.31 × 10^?8 g/Nm).     

利用表面硬度值间接获取镐形截齿钎焊层力学性能的方法研究

利用维氏硬度实验和数值模拟相结合的方法,间接得出了截齿表面各区域材料所对应的屈服强度值,建立了一种由实验硬度值HV获取截齿焊接接头等不易测量区域力学性能参数的方法。     

固溶处理对TiB2/6061复合材料硬度及耐磨性的影响

采用氟盐法制备了TiB₂质量分数为3%的原位合成TiB₂/6061复合材料,研究了固溶温度和固溶时间对复合材料硬度和耐磨性能的影响。结果表明:TiB₂颗粒弥散分布在6061铝合金基体中,明显细化6061铝合金基体晶粒。当固溶温度一定时,随固溶时间延长,复合材料的硬度和耐磨性可获得明显提高,但固溶时间在6~10 h时,复合材料的性能变化不显著。当固溶时间一定时,随固溶温度升高,复合材料硬度和耐磨性呈现先上升后下降的趋势。3wt%TiB₂/6061复合材料经530 ℃×10 h固溶处理后,硬度和耐磨性能最佳,相较于铸态硬度值提高了79.5％,磨损量减少了59.1%。固溶处理后复合材料的磨损表面犁沟变细变浅,材料脱落现象减少。